View TM9664FKFWG_877629.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

w
w
4U et he SPECIFICATION FOR LCD MODULE aS at .D w
Model No. TM9664FKFWG
om .c
Prepared by: Checked by : Verified by : Approved by:
w
w
.D w
t a
S a
e h
Date: Date: Date: Date:
t e
U 4
.c
m o
ee TIANMA MICROELECTRONICS CO., LTD Sh ta a D . w Ver. 1.0 w w
4U t
om .c
REVISION RECORD Date Ver. Ref. Page Revision No. Revision Items
1/23
1. General Specifications: 1.1 Display type: CSTN 1 1.2 Display color* : Display color: 221K(max) COLOR 2 Background* : Black (Red, Green, Blue dots are off state) 1.3 Polarizer mode: Transmissive/Negative 1.4 Viewing Angle: 6:00 1.5 Driving Method: 1/64 Duty 1.6 Backlight Type: LED (2 LAMPS) Backlight Color: WHITE 1.7 Controller: UC1682XGAD-U0 1.8 Data Transfer: 8 Bit Parallel 1.9 Operating Temperature: -20----+70ae Storage Temperature: -30----+80ae 1.10 Power Supply Voltage: VDD=3.0V 1.11 LCD Operating Voltage: VLCD=8.8V 1.12 Outline Dimensions: Refer to outline drawing on next page 1.13 Dot Matrix: 96 X 3 (RGB) X 64 Dots 1.14 Dot Size: 0.20(R+G+B)A 0.20(mm2) 1.15 Dot Pitch: 0.21A (mm2) 0.21 3 1.16 Weight: TBD* *1 Color tone is slightly changed by temperature and driving voltage. *2 Color tone will be changed by backlight. *3 TBD: To Be Determined.
2/23
2. Outline Drawing
3/23
3. LCD Module Part Numbering System
TM 96 64
FKFWG
IC PACKAGE G: COG TEMPRATURE RANGE W: WIDE TEMPERATURE RANGE BACKLIGHT TYPE F: TRANSMISSIVE, LED BACKLIGHT LCD TYPE K: COLOR STN MODE NEGATIVE MODULE SERIES MODULE TYPE DIGITS INDICATING: 96 (RGB) COLUMNS X 64 ROWS T: TIANMA M: MODULE
4/23
4. Circuit Block Diagram
5/23
5. Absolute Maximum Ratings Item Power Supply Voltage LCD Driving Voltage Operating Temperature Range Storage Temperature Range Symbol VDDVSS VLCD Min. -0.3 Max. +3.3 V +8.8 Unit
Ta=25ae Remark
TOP
-20
+70 ae Condensation
TST
-30
+80
6/23
6. Electrical Specifications and Instruction Code 6.1 Electrical characteristics Item Symbol Supply Voltage (Logic) Supply Voltage (LCD Drive) High VDD-Vss Min. Vss=0V, Ta=25ae Typ. Max. Unit
+2.8
+3.0
+3.20
V
VLCD VIH
VDD=3.0(c)
-
8.8
-
V
Input Signal Voltage
0.8VDD
-
VDD
V
Low
VIL
VDD=3.0(c)
0
-
0.2 VDD
V
Supply current (Logic)
IDD (VDD- VSS=3.0V) 0.8
mA
Supply Voltage (LED) Supply current (LED)
VLED
-
6.8
-
V
ILED
15.0
20.0
mA
7/23
6.2 Interface Signals
Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
Symbol VDD VDD VSS VSS VSS RD WR RS CS0 RST D7 D6 D5 D4 D3 D2 D1 D0 K A
Level
Description
3.0V SUPPLY POWER 3.0V SUPPLY POWER 0V 0V 0V H/L H/L H/L H/L H/L H/L H/L H/L H/L H/L H/L H/L H/L 0V GOUND GOUND GOUND READ SINGAL WRITE SINGAL SELECT CONTROL /DISPLAY CHIP SELECT RESET Data bus bit 7 Data bus bit 6 Data bus bit 5 Data bus bit 4 Data bus bit 3 Data bus bit 2 Data bus bit 1 Data bus bit 0 LED CATHODE
6.8V LED ANODE
8/23
6.3 Interface Timing Chart
CD tAS80 CS0 tCSSA80 WR0 WR1 Write D[X] tACC80 Read D[X] Parallel Bus Timing Characteristics (for 8080 MCU) (VDD=2.5V to 3.3V, Ta= -30 to +85 C) Symbol tAS80 tAH80 tCY80 Signal CD Description Address setup time Address hold time System cycle time 8 bits bus (read) (write) 4 bits bus (read) (write) Pulse width 8 bits (read) 4 bits Pulse width 8 bits (write) 4 bits High pulse width 8 bits bus (read) (write) 4 bits bus (read) (write) Data setup time Data hold time Read access time Output disable time Chip select setup time Condition Min. 0 10 140 128 128 128 65 35 35 35 65 35 35 35 30 10 - 10 10 10 20 Max. - - Units ns ns
o
tAH80 tCY80 tCSH80 tHPW80 tCSSD80
tPWR80, tPWW80
tDS80
tDH80
tOD80
tPWR80 tPWW80 tHPW80
WR1 WR0 WR0, WR1
- - -
ns ns ns
tDS80 tDH80 tACC80 tOD80 tSSA80 tCSSD80 tCSH80
D0~D7
- 50 50
ns ns ns
CL = 100pF
CS1/CS0
9/23
6.4 Instruction code
The following is a list of host commands supported by UC1680 C/D: W/R: 0: Control, 0: Write Cycle, 1: Data 1: Read Cycle
# Useful Data bits - Don't Care
Command 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 Write Data Byte Read Data Byte Get Status Set Column Address LSB Set Column Address MSB Set Temp. Compensation Set Panel Loading Set Pump Control Set Adv. Program Control (double byte command) Set Scroll Line LSB Set Scroll Line MSB Set Row Address LSB Set Row Address MSB Set VBIAS Potentiometer (double-byte command) Set Partial Display Control Set RAM Address Control Set Fixed Lines Set Line Rate Set All-Pixel-ON Set Inverse Display Set Display Enable Set Color Mask Set LCD Mapping Control Set Color Pattern Set Color Mode System Reset NOP Set Test Control (double byte command) C/D W/R 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 D7 # # 0 0 0 0 0 0 # 0 0 0 0 1 # 1 1 1 1 1 1 1 1 1 1 1 1 1 1 D6 # # MX 0 0 0 0 0 0 # 1 1 1 1 0 # 0 0 0 0 0 0 0 0 1 1 1 1 1 1 D5 D4 D3 # # DE # 0 1 1 0 # # # # # 0 # 0 1 # 0 0 0 1 0 0 0 0 0 0 0 D2 D1 D0 Action Write 1 byte Read 1 byte Get Status Set CA[3:0] Set CA[6:4] Set TC[1:0] Set PC[1:0] Set PC[3:2] Set APC[R][7:0], R = 0, or 1 Set SL[3:0] Set SL[7:4] Set RA[3:0] Set RA[7:4] Set PM[7:0] Set LC[9:8] Set AC[2:0] Set FL[3:0] Set LC[4:3] Set DC[1] Set DC[0] Set DC[3:2] Set MSK[2:0] Set LC[2:0] Set LC[5] Set LC[7:6] System Reset No operation For testing only. Do not use. Set BR[1:0] AC[3]=0, CA=CR AC[3]=1, CR=CA Set CEN[7:0] Set DST[7:0] Set DEN[7:0] Default N/A N/A N/A 0 0 0 01b 11b N/A 0 0 0 0 83H 0: Disable 001b 0 10b 0 0 10b 0 0 0 (BGR) 10b (65K) N/A N/A N/A 11b (12) AC[3]=0 AC[3]=1 159 0 159 # # # # MY WA 0 0 0 1 1 0 1 0 1 0 1 1 # # 0 0 0 1 1 0 1 1 0 0 # # 0 0 0 0 0 1 1 0 1 0 1 0 1 0 1 1 0 0 0 1 0 1 1 0 1 0 1 0 # # # # # # WS OD OS # # # # # # 1 # # 0 # # 1 # # 0 0 R # # # # # # # # # # # # # # # 0 0 1 # # # 1 # # # # # # # # 0 # # 1 0 # 1 1 # 1 # # # # # # # # 0 0 # 1 # # 0 1 0 0 1 1 1 TT
0
0 0 0 0 0 0 0 0 0
0
0 0 0 0 0 0 0 0 0
#
1 1 1 1 # 1 # 1 #
#
1 1 1 1 # 1 # 1 #
#
1 1 1 1 # 1 # 1 #
#
0 0 0 1 # 1 # 1 #
#
1 1 1 0 # 0 # 0 #
#
0 1 1 0 # 0 # 0 #
#
# 1 1 0 # 1 # 1 #
#
# 0 1 1 # 0 # 1 #
26 Set LCD Bias Ratio 27 Reset Cursor Update Mode 28 Set Cursor Update Mode 29 Set COM End 30 Set Partial Display Start 31 Set Partial Display End
10/23
Command Set Window Program 32 Starting Column Address Set Window Programming Starting Row Address Set Window Programming 34 Ending Column Address Set Window Programming 35 Ending Row Address 36 Enable window program 33 37 Set OTP Operation control 38 Set OTP Write Mask 39 Set VOTP1 Potentiometer 40 Set VOTP2 Potentiometer 41 Set OTP Write Timer 42 Set OTP Read Timer
C/D W/R 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
D7 1 1 # 1 1 # 1 1 1 # 1 # 1 # 1 # 1 #
D6 1 # 1 # 1 # 1 # 1 0 0 # 0 # 0 # 0 # 0 #
D5 1 # 1 # 1 # 1 # 1 1 # 1 # 1 # 1 # 1 # 1 #
D4 1 # 1 # 1 # 1 # 1 1 # 1 # 1 # 1 # 1 # 1 #
D3 0 # 0 # 0 # 0 # 1 1 # 1 # 1 # 1 # 1 # 1 #
D2 1 # 1 # 1 # 1 # 0 0 # 0 # 0 # 0 # 1 # 1 #
D1 0 # 0 # 1 # 1 # 0 0 # 0 # 1 # 1 # 0 # 0 #
D0 0 # 1 # 0 # 1 # # 0 # 1 # 0 # 1 # 0 # 1 #
Action Set WPC0[6:0] Set WPP0[7:0] Set WPC1[6:0] Set WPP1[7:0] Set AC[4] Set OTP0[5:0] Set OTP1[7:0] Set OTP2[7:0] Set OTP3[7:0] Set OTP4[7:0] Set OTP5[7:0]
Default 0 0 127 159 0: Disable 0 0 93 42 128 128
* Other than commands listed above, all other bit patterns may result in undefined behavior.
11/23
7. Optical Characteristics 7.1 Optical Characteristics Item Symbol Condition VLCD=8.8V Ta=25ae Min. Typ. Max. Unit
|x E Viewing Angle |E y Cr=2
|y = 0a E
-40
--
+40 Deg
|x = 0a E |E x=0a |E y=0a
|E=0a x
-40
--
+40
Contrast Ratio Turn on Turn off Red Color Of CIE CoordInate
Cr
40
-
-
Ton |E y=0a Toff x y |E x=0a |E y=0a |E x=0a |E y=0a |E x=0a |E y=0a
150
200 ms
Response Time
-
100 0.54 0.36 0.30 0.49 0.17 0.19
150 -
Green
x y x
Blue y
12/23
7.2 Definition of Optical Characteristics 7.2.1 Definition of Viewing Angle Top Top
Bottom 7.2.2 Definition of Contrast Ratio
Bottom
Contrast Ratio = B2/B1 =
Measuring Conditions: 1) Ambient Temperature: 7.2.3 Definition of Response time
unselected state brightness selected state brightness
25ae;
2) Frame frequency: 70.0Hz
Turn on time: t on = t d + t r Measuring Condition: 1) Operating Voltage:8.8V
Turn off time: t o f f = t d + t f 2) Frame frequency: 70.0Hz
13/23
7.3 Brightness Characteristic Item Brightness Uniformity Symbol Bp /p B Condition Ta=25ae3ae 30-80%RH Min. 150 Typ. 85 Max. Unit cd/m2 %
Note: 1. The data is measured after LEDs are turned on for 5 minutes. 2. Testing conditions LED: VLED = 6.8 V (DC) LCD: All dots are on (White color) 3. Brightness in the center of the LCD panel. 4. Definition of Uniformity (/p) B /p = Bp (Min.) / Bp (Max.) X 100 (%) B Bp (Max.) = Maximum brightness in 9 measurement spots Bp (Min.) = Minimum brightness in 9 measurement spots
14/23
8. Reliability 8.1 Content of Reliability Test Ta=25ae Test condition No. Test Item Content of Test 1 High Temperature Endurance test applying the high 80ae Storage storage temperature for a long time 240H Low Temperature Endurance test applying the low -30ae 2 Storage storage temperature for a long time 240H Endurance test applying the High Temperature electric stress (voltage |current) 3 70ae Operation and the thermal stress to the 240H element for a long time Endurance test applying the Low Temperature -20ae 4 electric stress under low Operation 240H temperature for a long time Endurance test applying the high 65ae High Temperature temperature and high humidity 5 90%RH /Humidity Storage storage for a long time 240H Endurance test applying the low and high temperature cycle Temperature -30ae /80ae -30 ae u80 ae u25 ae u25ae u u u 6 Cycle 30min 5min 30min 5min 10 cycles u(c)(c)(c)(c)(c)(c)(c)(c)(c)(c)(c)(c)u 1 cycle 10Hz~150Hz, Vibration Test Endurance test applying the 7 100m/s2, (package state) vibration during transportation 120min Half- sine wave, Shock Test Endurance test applying the shock 8 300m/s2, (package state) during transportation 18ms Endurance test applying the Atmospheric 25kPa 9 atmospheric pressure during Pressure Test 16H transportation by air
15/23
8.2 Failure Judgment Criterion Criterion Item Basic Specification Electrical specification Mechanical Specification Optical Characteristic Note Remark vvvvvv Test Item No. Failure Judgement Criterion 123456789 v v v v v v v v v Out of the basic Specification Out of the electrical specification Out of the mechanical specification v Out of the optical specification
vvvvv
vv
For test item refer to 8.1 Basic specification = Optical specification + Mechanical specification
16/23
9. Quality Level Examination At Ta=25ae or Test (unless otherwise stated) Inspection Min. Max. Unit IL AQL
Under normal Major External illumination and eyesight 1.0 Visual condition, the distance See Appendix A II Minor Inspection between eyes and LCD is 2.5 25cm. Under normal Major Display illumination and eyesight 1.0 See Appendix B II Defects condition, display on Minor inspection. 2.5 Note: Major defects: Open segment or common, Short, Serious damages, Leakage Miner defects: Others Sampling standard conforms to GB2828
17/23
10. Precautions for Use of LCD Modules 10.1 Handling Precautions 10.1.1 The display panel is made of glass. Do not subject it to a mechanical shock by dropping it from a high place, etc. 10.1.2 If the display panel is damaged and the liquid crystal substance inside it leaks out, be sure not to get any in your mouth, if the substance comes into contact with your skin or clothes, promptly wash it off using soap and water. 10.1.3 Do not apply excessive force to the display surface or the adjoining areas since this may cause the color tone to vary. 10.1.4 The polarizer covering the display surface of the LCD module is soft and easily scratched. Handle this polarizer carefully. 10.1.5 If the display surface is contaminated, breathe on the surface and gently wipe it with a soft dry cloth. If still not completely clear, moisten cloth with one of the following solvents: Isopropyl alcohol Ethyl alcohol Solvents other than those mentioned above may damage the polarizer. Especially, do not use the following: Water Ketone Aromatic solvents 10.1.6 Do not attempt to disassemble the LCD Module. 10.1.7 If the logic circuit power is off, do not apply the input signals. 10.1.8 To prevent destruction of the elements by static electricity, be careful to maintain an optimum work environment. a. Be sure to ground the body when handling the LCD Modules. b. Tools required for assembly, such as soldering irons, must be properly ground. c. To reduce the amount of static electricity generated, do not conduct assembly and other work under dry conditions. d. The LCD Module is coated with a film to protect the display surface. Be care when peeling off this protective film since static electricity may be generated.
18/23
10.2 Storage precautions 10.2.1 When storing the LCD modules, avoid exposure to direct sunlight or to the light of fluorescent lamps. 10.2.2 The LCD modules should be stored under the storage temperature range. If the LCD modules will be stored for a long time, the recommend condition is: Temperature : 0ae40ae Relatively humidity: U 80% 10.2.3 The LCD modules should be stored in the room without acid, alkali and harmful gas. 10.3 The LCD modules should be no falling and violent shocking during transportation, and also should avoid excessive press, water, damp and sunshine.
19/23
Appendix A Inspection items and criteria for appearance defects Items Leakage Rainbow Wrong polarizer attachment Polarizer Bubble between polarizer and glass Scratches of polarizer Black spot (in viewing area) Contents Criteria Not permitted According to the limit specimen Not permitted Not counted <0.3mm Max. 3 defects allowed 0.3mmU 0.5mm
According to the limit specimen Not counted Max. 3 spots allowed X<0.2mm X=(a+b)/2 0.2mmUU X 0.5mm Max. 3 spots (lines) allowed
Black line (in viewing area)
Not counted
Max. 3 lines allowed 0.02mmU 0.05mm aU bU 2.0mm
a<0.02mm
Progressive cracks
Not permitted
20/23
Appendix A Inspection item and criteria for appearance defects (continued) Items Contents Cracks on pads a U 3mm U 2mm b U W/5 Criteria c U 2 T/ Max. 2 cracks allowed
U W/5 T/2Cracks on contact side
a U 3mm U 2mm
b U 2 T/ T/2Glass Cracks
C shall be not reach the seal area Cracks on non-contact side a U 3mm U 2mm CU 0.5mm dU SW/3 Corner cracks e<2.0mm2 f<2.0mm2 b U 2 T/ T/2Max. 3 cracks allowed
21/23
Appendix B Inspection items and criteria for display defects Items Contents Criteria Not permitted Not permitted Not permitted According to the limit specimen According to the limit specimen Not counted X<0.1mm X=(a+b)/2 Pin holes and cracks in segment (DOT) Not counted A<0.1mm Max.2 dots allowed 0.1mmU 0.2mm AU D<0.25mm Max.3 dots allowed 0.1mmU 0.2mm XU Max.3 dots allowed
Open segment or open common Short Wrong viewing angle Contrast radio uneven Crosstalk
Not counted Black spot (in viewing area) X<0.1mm X=(a+b)/2 Not counted Black line (in viewing area) a<0.02mm
Max.3 spots allowed 0.1mmU 0.2mm XU Max.3 spots (lines) allowed
Max.3 lines allowed 0.02mmU 0.05mm aU bU 0.5mm
22/23
Appendix B Inspection items and criteria for display defects (continued) Items Content Criteria Not counted x1/4 0.1mm x=(a+b)/2 Max. 2 defects allowed 0.1mmU 0.2mm xU
Not counted Transformation of segment a1/4 0.1mm
Max. 1 defects allowed 0.1mmU 0.2mm aU D>0
Max.3 defects allowed
Max.2 defects allowed 0.8WU 1.2W aU
a=measured value of width W=nominal value of width
23/23

▲Up To Search▲

Price & Availability of TM9664FKFWG

	To Download TM9664FKFWG Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .